Install a replacement Epson EX3210 projector lamp

Written by
  • Shelagh M.
  • 6 years ago

This guide shows you how to replace the Epson EX3210 projector Epson EX3210 projector lamp

An authentic Epson EX3210 projector lamp will make all the difference in performance.

Why invest in authentic projector lamps

Look for the seal of approval before buying your Epson EX3210 projector lamp. Keep reading for the 6 reasons to avoid counterfeit lamps.

Find this lamp on Amazon sold by these authorized dealers:

6 reasons to avoid generic lamps:

Watching for end of life

It’s time to replace the Epson EX3210 projector lamp projector lamp when the following signs are seen:

  • The projected image gets darker or starts to deteriorate.
  • A message appears saying to replace the lamp when the projector is turned off
  • The projector lamp warning light flashes orange.

Installing the Projector Lamp Replacement

The Epson EX3210 projector lamp uses the Epson ELPLP67 projector lamp replacement.
Before installation:

  • Turn power button off wait for light to stop flashing.
  • Turn off power switch on Epson EX3210 projector lamp projector.
  • Unplug the power cord.
  • Allow the Epson EX3210 projector lamp projector to cool for one hour. It should be cool to the touch before changing the projector lamp.
  • Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

Caution: Don’t touch the actual bulb with your fingers since the oil from your skin can cause a black spot on the bulb.
Installing the Epson ELPLP67 projector lamp
Epson_EX3210_projector_Epson_ELPLP67_replacement_lampLoosen the lamp cover screw and slide the Epson EX3210 projector lamp cover off.
Epson_EX3210_projector_Epson_ELPLP67_remove_projector_lampLoosen the two screws holding the Epson ELPLP67 projector lamp in place.
NOTE: The Epson ELPLP67 projector lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps!
Epson_EX3210_projector_Epson_ELPLP67_replacement_projectors_lamp_step2Grab the Epson ELPLP67 projector lamp by the wire handle and gently pull the sprojector lamp out. Pulling too quickly can cause the bulb to shatter. Learn what to do should this happen. Gently insert the Epson ELPLP67 projector lamp making sure it’s facing the right way.
Epson_EX3210_projector_Epson_ELPLP67_insert_new_replacement_lampTighten the screws on the new Epson ELPLP67 projector lamp. Be sure not to tighten too much or the lamp may not work.
Replace the lamp cover and tighten the screw on the Epson EX3210 projector lamp projector lamp cover. You a ready to reset the projector lamp timer.
 

Reset the projector lamp timer

Reset the Epson EX3210 projector lamp projector Lamp Replacement Counter only when the Epson ELPLP67 projector lamp has been replaced.
Epson_EX3210_projector_Epson_ELPLP67_rest_lamp_timer

  • Press the MENU button on the remote control. The Lamp Reset Menu will appear.
  • Scroll down to the RESET LAMP HOURS. Press ENTER.
  • A prompt appears asking if you want to RESET LAMP HOURS?
  • Select YES and press ENTER.
  • Press MENU to exit.

Prolong the life of the  projector lamp:

Extend the life of the newly installed Epson ELPLP67 projector lamp with the following tips:

  • Keep your air filters clean to avoid overheating the projector.
  • Turn off the Epson EX3210 projector lamp projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
  • Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
  • Learn more with Top tips for extending DLP projector lamp life

 

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Shares