Use this guide to install a replacement
Dukane ImagePro 8769 projector lamp.
Warning sign
Your Dukane ImagePro 8769 projector lamp has a life of approximately 2100 hours (up to 3100 hours in Eco mode) depending on maintenance and frequency of use. Don’t leave replacing the projector lamp to the last minute or you may have a projector that will not turn on.
When the warning B“The lamp has reached the end of its usable life. Please replace the lamp” shows up on your screen replace the projector lamp immediately.
If you have wait too long your Dukane ImagePro 8769 will go into standby mode. Press the HELP button on the remote control for 10 seconds to reset the lamp timer to zero and replace the projector lamp immediately. Don’t keep using the lamp since it will shut down the projector immediately.
Other warning signs of end of life are an image that has become distorted, faded or with strange colors.
Reduce stress with authentic
There are plenty of online options for a replacement Dukane ImagePro 8769 projector lamp. The problem is avoiding counterfeit knock-offs that can damage your projector.
6 reasons to avoid counterfeits:
- no safeguards to protect your eyesight
- toxic materials and carcinogenic parts including Krypton-85
- shorter lamp life than original lamps
- prone to explosions
- damage to the sensitive electronics in your projectors
- no guarantee or refunds and your warranty is void
Find this lamp on Amazon from these authorized dealers:
- 456-8767A Dukane Projector Lamp Replacement. Projector Lamp Assembly with High Quality Genuine Original Ushio Bulb Inside.
- AuraBeam Professional Dukane 456-8767 Projector Replacement Lamp with Housing (Powered by Ushio)
- 456-8767A Dukane Projector Lamp Replacement. Projector Lamp Assembly with High Quality Genuine Original Ushio Bulb Inside.
- SpArc Platinum Dukane 456-8767 Projector Replacement Lamp with Housing
- SpArc Bronze Dukane 456-8767 Projector Replacement Lamp with Housing
Replacing the projector lamp
The Dukane ImagePro 8769 projector uses the Dukane 456-8767A projector lamp. Before installing a new projector lamp do the following safety steps:
- Reduce the risk of electrical shock by disconnecting the power cord on the projector.
- Reduce the risk of severe burns by allowing the projector to cool for at least 45 minutes. It should be cool to the touch.
Protect the Dukane ImagePro 8769 projector’s top surface by placing it face down on a soft surface. to access the lamp cover.
Use a Philips screwdriver to push and release the tab. Push up and remove the lamp cover. NOTE: There is an interlock on this case to prevent the risk of electrical shock. Do not attempt to circumvent this interlock.
Loosen the two screws securing the Dukane 456-8767A projector lamp. The screws are not removable so will start start freewheeling. Remove the lamp by grabbing onto the indents on the lamp and pulling up.
Never force the lamp out; pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.
NOTE: The Dukane 456-8767A projector lamp projector lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps!
Gently put in a new Dukane 456-8767A projector lamp and tighten the two screws to hold the lamp in place. Make sure the screws are secure as a loose screw can cause a bad connection while a over tightened screw may cause the lamp to notwork.
Replace the lamp cover on the projector.
Slip the lamp cover back until it snaps into place.
Restart the projector to reset the lamp timer.
Resetting the lamp timer
It’s important to set the lamp timer so the Dukane ImagePro 8769 can accurately track the life of the newly installed Dukane 456-8767A projector lamp.
To reset the lamp timer go to the Dukane ImagePro 8769 Default Menu. Scroll down to Clear Lamp Hour Meter to reset the lamp timer.
Extend the life of the Dukane 456-8767A projector lamp:
- Keep your air filters clean to avoid overheating the projector.
- Setting Lamp Power to Economic Mode.
- Learn more with Top tips for extending DLP projector lamp life.
