Replacing the Mitsubishi WD-73842 RPTV lamp

Written by
  • Shelagh M.
  • 12 years ago

Mitsubishi WD-73842 Mitsubishi 915B455011 / 915B455A11 Lamp

Follow this step-by-step guide for replacing the lamp in the Mitsubishi WD-73842 RPTV.

When the picture on your Mitsubishi WD-73C12 RPTV becomes dimmer it’s time to replace the Mitsubishi 915B455011/915B455A11 lamp. When the lamp is no longer working the Status Light on the front of the Mitsubishi WD-73842 panel will begin blinking red.
Since the 915B455011 / 915B455A11 lamp is the only source of light for the TV when it has reached its end of life, the Mitsubishi WD-738422 will not turn on.

Invest in an authentic lamp

Buy your Mitsubishi 915B455011/915B455A11 lamp from an authorized manufacturer and avoid the lower-priced generic lamps. These knock-off lamps are made with inferior, counterfeit parts that can damage the sensitive mechanisms in your Mitsubishi WD-73842 RPTV. These generic lamps advertise as compatible but may end up costing you more since they have a shorter lamp and are prone to explosions. Buying an authentic lamp from a legitimate source keeps your projector under warranty and gives you a solid guarantee that the lamp you are installing is suitable for your projector.
Learn the 7 Ways to spot a counterfeit lamp.

Installing the new Mitsubishi 915B455011/915B455A11

Before installation: Turn off the TV and allow it to cool for one hour. Failure to do so can put you at risk of burning yourself since the Mitsubishi WD-73842 operates under high heat.
Mitsubishi WD-73842 location of panel, Mitsubishi 915B455011 / 915B455A11 Lamp
 

  • After TV has cooled, turn the TV around to access the lamp cover located at the back of the Mitsubishi WD-73842 RPTV.

Mitsubishi WD-73842 lamp cover off, Mitsubishi 915B455011 / 915B455A11 Lamp

  • Using a #2 Philips screwdriver, loosen the screw holding the cover in place. Put the cover to one side.

 
 
 
 
Mitsubishi WD-73842 lamp screw rempved, Mitsubishi 915B455011 / 915B455A11 Lamp

  • Loosen the screw securing the lamp cartridge, releasing it from the mating threads. This is a captive screw so it will not be separated the lamp cartridge.)
  • When the screw is loosened, gently grasp the handle on the lamp cartridge and pull the lamp straight out. DO NOT TILT, as there may be glass fragments that will fall inside the TV.
  • If this happens, carefully pick up the larger shards wearing rubber gloves. Take a cloth just damp enough to pick up the small shreds. It’s important to pick up the broken lamps since this lamps does have mercury. Read more about proper clean-up from the EPA.
  • Learn what to do should the bulb shatter.
  • Take out the bag supplied with your new lamp and open it up. You’ll store the old lamp in this bag.
  • Put the old lamp gently into the opened bag. Close the bag.
  • Gently slide in the new Mitsubishi 915B455011 / 915B455A11 Lamp into the slot, making sure not to tile the lamp.
  • Tighten the screw in the lamp.
  • Replace the cover and tighten the screws.

NOTE: The Mitsubishi 915B455011 / 915B455A11 Lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps! If you bought from an authentic manufacturer, they will recycle the lamp for you at no extra cost (another reason to buy authentic lamps).

Learn how to extend the Mitsubishi 915B455011 / 915B455A11 lamp life in by reading 7 Tips for extending RPTV lamp life.

Comments

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Shares