4 Steps to a new Optoma EP753H projector lamp

Written by
  • Shelagh M.
  • 11 years ago

Optoma_EP753H_projector_BL-FU200AFollow this step-by-step installation guide for installing a new Optoma EP753 projector lamp.

Lamp Replacement Warning

The projector will detect the lamp life itself. It will show you a warning message “Lamp is running out of standard lifetime. Be sure to replace the lamp as soon as possible.” When you see this message, change the Optoma EP753H projector lamp as soon as possible. You may also see the Lamp LED start flashing orange and notice the image has gotten dark or started to deteriorate.

 Buy the correct lamp

Your Optoma EP753H uses the Optoma BL-FU200A (SP.83601.001C) lamp. There are lots of choices out there for buying your lamp but since selling online has few regulations, it’s easy to get duped into buying an inferior knock-off lamp posing as an authentic one. Watch for telltale signs you are about to purchase a counterfeit lamp:

Why avoid generics:

Buy this lamp on Amazon from the following authorized dealers:

Installing the Optoma BL-FU200A lamp

Your Optoma EP753H projector needs a Optoma BL-FU200A  lamp. Follow these important safety tips before changing the lamp:

  • Switch off the power to the projector by pressing the Power/Standby button.
  • Disconnect the power cord.
  • Allow the projector to cool down for at least 30 minutes. If should be cool to the touch. These projectors run using high temperatures and you can burn yourself badly if you don’t allow the projector to cool down.

Optoma_EP753H_remove_lamp_cover_BL-FU200A Step 1: Use a screwdriver to loosen the screws holding the lamp cover in place. Make sure you have followed the safety tips before taking the cover off. The Optoma EP753 projector should be cool to the touch.
Step 2: Remove the lamp cover and place to one side. Don’t lose the screws to the cover as the Optoma EP753H projector will not turn back on until the lamp cover has been properly installed.
Step 3: Remove all three screws holding the Optoma BL-FU200A (SP.83601.001C) lamp in place.

Step 4: Lift the wire handle and gently remove it from the projector. Be careful not to hit the lamp or you can cause it to break.

  • Take the new Optoma BL-FU200A  lamp out of its packaging and lift the handle on the lamp. Gently place it into the projector making sure not to touch the actual bulb. Oil from fingerprint marks can burn black spots onto the lamp when it heats up.

Once the lamp is installed:

  • Tighten the screws on the lamp.
  • Close the lid. Tighten the cover screws.
  • You are now ready to reset the lamp timer.

Reset the Optoma EP753H lamp timer

Your Optoma EP753H comes equipped with an automatic lamp timer that tracks the number of hours left for the Optoma BL-FU200A lamp. Each time you change the lamp you need to reset the lamp timer. Failure to do so may cause the projector to use the lamp over the recommended period of time resulting in the lamp exploding.

  • Press the Menu button to open the On-Screen-Data (OSD) menu.
  • Press the right/left arrow button to move to the Management menu.
  • Press the right/left arrow button button to move down to Lamp Reset.
  • Press the right arrow or Enter button to enter Status menu.
  • Press the up/down arrow button to move down to Lamp Hour Reset.
  • Press the right arrow or Enter button to select Reset option.
  • Press the down button, then up button, then left button, then right button.
  • The Status menu appears again showing the Lamp Hours reset to zero.

Learn the TOP Tips for extending the lamp life in your Optoma EP753H projector.

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.