When to replace the Sanyo POA-LMP14 projector lamp

Written by
  • Shelagh M.
  • 10 years ago
Sanyo POA-LMP14, Sanyo POA-LMP14 (610-265-8828)

Sanyo POA-LMP14

The life expectancy of your Sanyo POA-LMP14 (service parts no 610-265-8828) lamp depends on the amount of usage and whether the air filters are cleaned on a regular basis. A build up of dust on the filters will reduce the cooling fans effectiveness and may cause the lamp to overheat.
The life of the Sanyo POA-LMP14 (610-265-8828) lamp runs anywhere from 1,000 to 3,000 hours. It’s life cycle will vary  depending on how often  depending your projector is use and whether there is regular maintenance of the filters.
It’s always a good idea to keep a spare lamp on hand so you can replace the lamp immediately and not wait to use the projector.
The best type of lamp to buy is one that has been guaranteed authentic and created by approved manufacturers who use the correct parts for the lamp. Knock-off lamps use counterfeit parts that can explode inside the projector or not fit properly thereby damaging the sensitive mechanism in the projector. The initial low cost of these counterfeit lamps may end up costing you more money in the long run if your projector is ruined. Buy an authentic Sanyo POA-LMP14 (service parts no 610-265-8828) will maintain your warranty while providing you with a manufacturer’s guarantee.

The Sanyo POA-LMP14 can be used in the following projectors:

For step-by-step instructions on how to replace the Sanyo POA-LMP14 (service parts no 610-265-8828) projector lamp, please click on your specific model listed below:

Sanyo 5600N Projector
Sanyo 5600N Projector

Click here for step-by-step instructions on how to change the Sanyo POA-LMP14 (service parts no 610-265-8828) projector lamp for the Sanyo PLC-5600N projector.

 

Sanyo PLC-5605B Projector

Sanyo PLC-5605B Projector

Click here for step-by-step instructions on how to change the Sanyo POA-LMP14 (service parts no 610-265-8828) projector lamp for the Sanyo PLC-5605B/PLC-560P projector.

Sanyo PLC 8810 Projector

Sanyo PLC 8810 Projector

 

Click here for step-by-step instructions on how to change the Sanyo POA-LMP14 (service parts no 610-265-8828) projector lamp for the Sanyo PLC-8810 projector.

 

Sanyo PLC-8800N Projector

Sanyo PLC-8800N Projector

Click here for step-by-step instructions on how to change the Sanyo POA-LMP14 (service parts no 610-265-8828) projector lamp for the Sanyo PLC-8800N projector.

 

Sanyo PLC-8805B Projector

Sanyo PLC-8805B Projector

Click here for step-by-step instructions on how to change the Sanyo POA-LMP14 (service parts no 610-265-8828) projector lamp for the Sanyo PLC-8805B/PLC-8805P projector.

Sanyo PLC-8815E Projector

Sanyo PLC-8815E Projector

Click here for step-by-step instructions on how to change the Sanyo POA-LMP14 (service parts no 610-265-8828) projector lamp for the Sanyo PLC-8815E/PLC-8815B/PLC-8815P projector.

 
Learn more with Top tips for extending DLP projector lamp life.

Replace_lamp_keep_plastic_cageLooking for an enviro-friendly option that is also less expensive? Consider just replacing the bulb instead of the whole lamp housing. For more info and a how-to guide watch our step-by-step video on replacing only the Sanyo POA-LMP14 bulb.

 
 

Leave a Reply

Your email address will not be published.

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Shares