Installation guide for the Optoma HD67 projector lamp

Written by
  • Shelagh M.
  • 9 years ago

Optoma_HD67_Optoma_BL-FU185A_SP.8EH01GC01_projector_lampThis D.I.Y guide shows you how the replace the Optoma HD67 projector lamp.

When to replace the projector lamp

Optoma_HD67_lamp_warning_Optoma_BL-FU185A_projector_lampWhen it’s time to replace the Optoma HD67 projector lamp you’ll see a lamp replacement message flash on screen. Change the lamp in your Optoma HD67 projector immediately. You may also notice the Lamp-LED light flashing red or the picture quality starting to get poor resolution with washed out colours.

Why buy authentic?

The Internet has been flooded with generic projector lamps stating they are “compatible” with Optoma HD67 projectors. Consider the source before purchasing. Generic lamps have a long list of problems:

Learn how to buy an authentic lamp. Look for a registered OEM manufacturer in North America using the correct materials and specifications for your Optoma HD67 replacement projector lamp.

Find this lamp sold on Amazon by these authorized dealers:

Installing the Optoma BL-FU185A projector lamp

Before replacing the Optoma BL-FU185A  projector lamp follow these important safety tips:

  • Switch off the power to the Optoma HD67 projector by pressing the Power/Standby button.
  • Disconnect the power cord.
  • Allow the projector to cool down for at least 30 minutes. If should be cool to the touch. These projectors run using high temperatures and you can burn yourself badly if you don’t allow the projector to cool down.

Optoma_HD67_replacing_Optoma_BL-FU185A_projector_lamp 1. Use a screwdriver to undo the two screws holding the projector lamp cover in place. The screws on the lamp cover and the lamp cannot be removed.
2. Remove the lid and place to one side. Don’t lose the lid as the Optoma HD67 projector will not turn back on until the lamp cover has been properly installed.
3. Remove the two screws holding the Optoma BL-FU185A projector lamp in place. Note: The used Optoma BL-FU185A projector lamp contains mercury and should be properly recycled. Don’t throw it into regular garbage.
Optoma_HD67_replace_Optoma_BL-FU185A_projector_lamp4. Lift up the wire handle on the Optoma BL-FU185A lamp and slowly remove it from the projector. Be careful not to bang the lamp against the projector as this may case the bulb to break. Learn what to do if the lamp has exploded inside the projector.
5. Remove the new Optoma BL-FU185A  from its packaging. Taking care not to touch the actual bulb, lift up the handle on the new projector lamp and insert it gently into the Optoma HD67 projector.
6. Tighten the two screws on the lamp.
7. Replace the lamp cover and tighten its two screws.

Reset the Lamp Replacement Timer

The Optoma HD67 projector has an automatic lamp timer that tracks the numbers of hours left in the projector lamp. When the Optoma BL-FU185A  is approaching end of life, the lamp replacement timer will trigger the warning system. If you don’t reset the lamp replacement timer you run the risk of the lamp being used beyond its recommended life and possibly exploding in the projector. Should the lamp explode, learn what to do. To reset the Lamp Replacement Timer:
 
Optoma_HD67_lamp_control_menu_Optoma_BL-FU185A_projector_lamp

  • Turn on the projector.
  • Using the remote press MENU
  • Select OPTIONS
  • Select LAMP SETTINGS
  • Select LAMP RESET
  • Select YES.
  • Press MENU to exit.

Extend the life of the Optoma BL-FU185A  projector lamp:

  • Chose the “STD” mode to to dim the projector lamp and lower power consumption. This will extend the lamp life by up to 130%.
  • Keep your air filters clean to avoid overheating the projector.
  • Every 24 hours, turn off the projector and let it stand for 1 hour
  • Make sure there is enough airflow around the Optoma HD67 projector particularly if it’s been permanently mounted.
  • Learn more with Top tips for extending DLP projector lamp life.

Green your Optoma HD67 projector

Optoma-BL-FU185A_replacement_bulb_training_videoThe Optoma HD67 projector has the option of re-using the existing lamp cage and replacing only the actual bulb. You recycle and reduce waste this way. Watch our Optoma BL-FU185A training video to learn more.

Comments

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Shares