Replacement guide for Optoma EP747T projector lamp

Written by
  • Shelagh M.
  • 11 years ago

Optoma_EP747T_projectors_Optoma_BL-FP230A_projector_lampOur step-by-step guide shows how to replace Optoma EP747T projector lamp

At 3o hours, when the Optoma EP747T projector lamp is reaching end of life, you will see the Lamp Replacement message on your screen.
Be sure to buy authentic lamps and avoid generic lamps. Optoma EP747T projector lamp generic lamps may appear to be a bargain but actually less durable than authentic lamp.
Find this lamp from the following OEM manufacturers on Amazon:

Replace the Optoma EP747T projector lamp

NOTE: The Optoma BL-FP230A lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps! If you bought from an authentic manufacturer they will recycle the lamp for you at no extra cost. Generic manufacturers don’t recycle.

Step 1

Lamp_Replacement_Remove_screws_Optoma_BL-FP230H_projector_lamp_projector_EP747T

  • Switch off the power to the Optoma EP747T projector by pressing the Power/Standby button.
  • Allow the projector to cool down for at least 30 minutes. If should be cool to the touch. These projectors run using high temperatures and you can burn yourself badly if you don’t allow the projector to cool down.
  • Disconnect the power cord. Using a screwdriver, remove the screws holding the cover in place. Push the cover up to remove.

Replacement_remove_cover_Optoma_BL-FP230A_projector_lamp_Optoma_EP747T_projector
EP747T_Lamp_Replacement_remove_lamp_screws_Optoma_BL-FP230A_projector_lamp

Step 2

  • Use a screwdriver to remove the two screws holding the Optoma EP747T lamp module in place.
  • Slowly put out the old lamp by grabbing the edge of the lamp. Be careful not to bang the lamp against the projector as this may case the bulb to break. Learn what to do if the lamp has exploded inside the projector.

Optoma_EP747T_projector_remove_ BL-FP230A_lamp

Step 3

  • Place the new Optoma BL-FP230A (SP.83R01G001) into the Optoma EP747T projector. Tighten the two screws on the lamp. Replace the lamp cover and tighten its two screws.
  • You must now reset the Lamp Replacement Timer.

Reset the lamp timing on the Optoma EP747T

Optoma_EP747T_projector_Lamp_Control_Menu_Optoma_BL-FP230A_projector_lamp

  • Press the Menu option on either the remote or on the projector.
  • Scroll over the Lamp Setting. Press enter.
  • Select Reset Lamp Hours. Press Enter
  • The Execute/Cancel command line will appear.
  • Scroll over to choose Execute. Press Enter.
  • The lamp hours will be reset to zero.

Turn on the Eco Mode to lower power consumption and extend the lamp life by 130%.

Why buy authentic lamps?

Optoma_BL-FP230A_projector_lamp_EP747_Lamp_Replace_LampThere are lots of choices out there on the Internet. Since selling online has few regulations, it’s easy to get duped into buying an inferior knock-off lamp posing as an authentic Optoma BL-FP230A.
The tell tale sign is a price that seems too good to be true. These counterfeit manufacturers will advertise their lamp as “compatible.” However, it’s anything but compatible.
Learn how to spot the copycat fake lamps with 7 Ways to Spot a Counterfeit Lamp.

6 reasons to avoid generics:

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Shares