3 steps to a new Sanyo PLC-SU33 projector lamp

Written by
  • Shelagh M.
  • 12 years ago
Sanyo PLC-XU33 projector, Sanyo POA-LMP35 service part no 610 293 2751

Sanyo PLC-XU33 projector

If the picture on your Sanyo PLC-SU33  projector is is dim or looks unnatural the new Sanyo POA-LMP35 (service part no 610 293 2751) is reaching its end of life. You may also notice the Replace Lamp Indicator light on the front panel is yellow. Replace the Sanyo POA-LMP35 in the Sanyo PLC-SU33 projector by following the step-by-step guide below.

STEP ONE: Purchasing the correct projector lamp

The best thing you can do to prolong the life of your Sanyo PLC-SU33 and save money is to invest in an original Sanyo POA-LMP35 (610-293-2751) projector lamp. Generic lamps look like a great bargain since they are generally cheaper, however, these knock-off lamps are created with inferior materials. They are susceptible to explosions, have a shorter life span and can damage the precise components in your Sanyo PLC-SU33 projector.   Installing a knock-off generic lamp also voids your warranty. Learn more about spotting dangerous projector lamps by reading our article: 7 tips for spotting counterfeits.

STEP TWO: Installing the new Sanyo POA-LMP35 lampLC-SU32 lamp cover, Sanyo POA-LMP35 service part no 610 293 2751

  • Allow the Sanyo PLC-SU33 projector to thoroughly cool before changing the lamp. Turn off the projector, unplug the AC cord and allow 45 to 60 minutes for the projector to cool. These projectors operate under high heat and there is a possibility of being burned, if the projector is not fully cooled before changing the Sanyo POA-LMP35 (service part no 610 293 2751)lamp.
  • The lamp cover for the Sanyo PLC-SU33 is at the bottom of the projector. Gently turn projector over and loosen the screw holding the cover in place. Place the cover to one side.
  • Inside you’ll find the Sanyo POA-LMP35 (service part no 6102932751) lamp cage. Loosen both screws holding the lamp cage in place. Grab the lamp handle and gently lift the lamp out of its socket. Place to one side. Be sure to dispose of the used lamp through a local recycling program. Don’t throw this lamp into the regular garbage as it contains mercury.Sanyo PLC-SU33 lamp assembly, Sanyo POA-LMP35 service part no 610 293 2751
  • Taking the new Sanyo POA-LMP35 (service part no 610 293 2751) lamp assembly by the handle place it into the slot. Avoid touching the actual bulb as the oil from your fingers can burn a black spot on the lenses or you can accidentally break the bulb. Don’t force the lamp into place — it should slide into the slot easily.
  • Once the lamp is in, tighten both screws on the Sanyo POA-LMP35 (service part no 610293 2751) lamp assembly. Make sure the screws have been tightened properly or the Sanyo PLC-SU33 projector will not turn on.
  • Replace the Lamp Cover and tighten the screw. Re-connect the power cord and turn on the Sanyo PLC-SU33 projector If the Sanyo POA-LMP33 lamp does not turn on after the warm-up period, try re-installing the lamp.
  • Reset the Lamp Replace Counter by following the instructions below.

NOTE: Your old  Sanyo POA-LMP35 (service part no 6102932751) lamp should be properly recycled. These lamps contain mercury and can’t be placed into common garbage.
 

STEP THREE: Reset the Sanyo PLC-SU33 Lamp Replace Counter

The Lamp Replace Counter for the Sanyo PLC-SU33 will track the correct age of your newly installed lamp and trigger the Lamp Replace Indicator. Failure to reset the counter may result in the projector not tracking the end of life for the  Sanyo POA-LMP35 (6102932751) and letting the projector inadvertently use the lamp past its normal life cycle. Your Sanyo PLC-SU33 may stop working suddenly if the Lamp Replace Counter has not been properly set.
Sanyo PLC-SU33 lamp reset screen, Sanyo POA-LMP35 service part no 6102932751

  • Press the MENU Button to display the MAIN MENU. Press the POINT LEFT/RIGHT button and scroll right to select SETTING.
  • Press the SELECT button to display the SETTING DISPLAY menu.
  • Press the POINT DOWN button (a red arrow will appear).
  • Move the red arrow to the LAMP AGE and then press the SELECT button.
  • The message “Lamp replace counter reset?”  appears. Move the arrow down to YES and press the SELECT button.
  • Move the arrow to QUIT and press the SELECT button.

 

Extend the life of the Sanyo POA-LMP48 projector lamp

Extend the life of your newly installed  Sanyo POA-LMP35 (service part no 610 293 2751) by following these helpful tips:

  • Wait at least five minutes before turning the Sanyo PLC-SU33 off.
  • Don’t operate the projector continuously without letting it stand for at least one hour turned off every 24 hours.
  • Cleaning the air filter regularly will also prolong the life of the Sanyo POA-LMP35 (service part no 6102932751) and prevent the Sanyo PLC-SU33 projector from overheating.

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Shares