3 Steps to a new Epson EB-W10 projector

Written by
  • Shelagh M.
  • 10 years ago

Epson_EB-W10_projector_Epson_projecor_lamp_ELPLP58Replace the Epson EB-W10 projector lamp in three easy steps using this guide.

Step 1: Invest in authentic

Save yourself hassles and protect your projector by investing in an authentic Epson EB-W10 projector lamp. Look the seal of approval and learn to spot copycat lamps posing as authentic lamps. You may be tempted to buy a cheaper generic lamp in order to save money. While these knock-off lamps appear to be a bargain, they  end up costing  more money in the long run .
Why avoid generics:

Find this lamp on Amazon sold by these authorized dealers:

Step 2: Recognize end of warning signs

Epson_EB-W10_projector_Epson_ELPLP58_check_projector_lamp_hoursKnow when the  Epson EB-W10 projector lamp is reaching end of life so you can be prepared with a new lamp. When the projector lamp indicator is continually flaand continue it’s time to replace the lamp.
Epson_EB-W10_projector_Epson_ELPLP58_projector_lamp_lamp_warningWhen the message Replace the lamp appears on the screen it’s also time for a new projector lamp.  You may also the image on screen gets darker or starts deteriorate altogether. In order to maintain projector brightness and image quality, replace with a new Epson LPLP58 (V13H010L58) projector lamp as soon as possible.
The Epson EB-W10 projector lamp can last for close to 4,000 hours when the power consumption is set to NORMAL and up to 5,000 hours if the ECO option is used. You can check the hours left on the ELPLP58 (V13H010L58) projector lamp from the INFO Menu access off the Main Menu.

Installing a new ELPLP58 (V13H010L58) projector lamp

Before replacing the ELPLP58 (V13H010L58) projector lamp follow these important safety rules:

  1. Always unplug the power cord on the Epson EB-W10 projector before replacing the projector lamp.
  2. This projector operates using high temperature. Wait at least 60 minutes before replacing the lamp so you don’t run the risk of getting burned.
  3. Never touch the bare projector lamp bulb as the oil from your fingers will burn black marks onto the projector lamp when it heats up.
  4. Never operate the Epson EB-W10 projector with the projector lamp removed.

Remove the projector lamp cover screws and place to one side.
Epson_EB-W10_projector_Epson_ELPLP58__remove_projector_lamp_screwsLoosen the two screws holding the Epson ELPLP58 (V13H010L58) projector lamp in place (you can’t remove them).
Gently lift out the Epson LPLP58 projector lamp taking care not to bang it against the projector. NOTE: The LPLP58 projector lamp contains mercury and should not be thrown into regular garbage. Recycle this lamp!
Gently insert the new Epson LPLP58 projector lamp. Make sure it fits into the Epson EB-W10 projector properly. (Check that it’s facing the right way.) Tighten the Epson LPLP58 projector lamp.
You can know reset the lamp timer.

Reset the lamp timer

After you replace the lamp, you need to reset the Epson Epson EB-W10 projector lamp timer using the projector’s menu system.

  • Press the MENU button on the remote control or on the projector’s control panel. You see the main menu.
  • Select the RESET menu. Press ENTER.
  • Scroll down to select RESET LAMP HOURS. Press ENTER.
  • A prompt filed appears asking if you want to reset the lamp timer. Select YES. Press ENTER.
  • Press MENU to exit.

Longer life for the ELPLP58 (V13H010L58) projector lamp

Extend the life of the Epson ELPLP58 (V13H010L58) projector lamp with the following tips:

  • Set the Power Consumption to ECO option.
  • Clean the air filters regularly so the Epson EB-W10 projector doesn’t overheat.
  • Make sure there is enough airflow around the projector.
  • Turn it off when it’s not in use.
  • Learn more: Top tips for extending DLP projector lamp life.

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.