Changing the Vivitek H1080 projector lamp

Written by
  • Shelagh M.
  • 9 years ago

Vivitek_H1080_projector_Vivitek_5811116206_projector_lampThe Vivitek H1080 projector lamp takes under 15 minutes to replace. Follow our guide for help.

Watch your projector lamp hours

Check the Vivitek H1080 projector lamp life if you notice the picture becoming distorted or the Power LED flashing 5 times consecutively. To check the lamp hours:

  • Press the Menu button to open the OSD menu.
  • Press left/right arrow keys to move button to move to the STATUS Menu.
  • The LAMP HOUR field displays the number of hours the lamp has been in use.
  • You can expect 2000 hours lamp life. 3000 hours if Eco Mode has been turned on.

Buy the right Vivitek H1080 projector lamp!

Your Vivitek H1080 projector uses the Vivitek 5811116206-S projector lamp. Be sure the purchase an authentic projector lamp and avoid the temptation of a the generic lamps with their bargain prices. Generic projector lamps have a much shorter lamp life and are prone to explosions. They are usually manufactured with toxic and dangerous substitutes that mean the lamps can’t  be properly calibrated. They often end up damaging the sophisticated electronics in your Vivitek H1080.  Vivitek wants you to avoid these lamps as well and voids your projector warranty if  you install a  generic. Save yourself the hassles and go an authentic Vivitek 5811116206-S projector  lamp.

Replace the 5811116206-S lamp

Before changing the Vivitek 5811116206-S lamp:

  • Reduce the risk of electrical shock by disconnecting the power cord on the Vivitek H1080 projector.
  • Reduce the risk of severe burns by allowing the projector to cool for at least 45 minutes.

Vivitek_H1080_projector_remove_cover_Screws_Vivitek_5811116206_projector_lamp

  • Turn the projector around to locate the lamp cover screw. Remove the captive screw holding the lamp cover place.

Vivitek_H1080_projector_remove_lamp_cover_Vivitek_5811116206_projector_lamp

  • Gently slide off the lamp cover and place it to one side. You will need to re-install the cover before turning on the Vivitek H1080 projector again.

Vivitek_H1080_projector_remove_lamp_screws_Vivitek_5811116206_projector _lamp
 

Vivitek_H1080_projector_remove_Vivitek_5811116206_lamp_projector _lamp

NOTE: The 5811116206-S lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps!
Vivitek_H1080_projector_install_Vivitek_5811116206_projector _lamp
 

  • Lift up the wire handle on the new Vivitek 5811116206-S projector lamp and gently guide it into the H1080 projector.
  • Take care not to touch the actual bulb as the oil from your fingers will smudges that will burn into a black spots when the projector heats up.
  • Tighten the lamp screw.
  • Re-install the H1080 lamp cover and tighten the screw.
  • Reset the total lamp hour timer.

Resetting the Lamp Hour Timer

It’s important to only reset the lamp timer when the Vivitek 5811116206-S lamp has been replaced. Resetting the lamp timer without changing the lamp can make it work beyond its recommended hours and cause harm to your Vivitek H1080 projector.

  • Press the Menu button to open the OSD menu.
  • Press left/right arrow keys to move to the Setup menu.
  • Press up/down arrows to move to the Advanced menu
  • Press Enter.
  • Press the cursor up/down arrows button to Lamp Hour Reset.
  • Press Enter.
  • A message will appear saying the Lamp Hour has been reset to zero.
  • Press the Menu button to return to the main Setup menu.

Extending the life of the Vivitek 5811116206-S projector  lamp:

  • Keep your air filters clean to avoid overheating the projector.
  • Use the Lamp Power option on the Vivitek H1080 projector and set to Eco Mode to reduce the amount of power used but extend lamp life.
  • Learn more with Top tips for extending DLP projector lamp life.

 

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Shares