4 Steps to a new Optoma EP719 projector lamp

Written by
  • Shelagh M.
  • 11 years ago

Optoma_EP719_projectorUse our step-by-step guide to install a new Optoma EP719 projector lamp.

It’s simple to replace the Optoma EP719 projector lamp when you follow these steps.

Step One: Buy the right lamp!

Before you replace the Optoma EP719 projector projector lamp check for the seal of approval to be sure you’re getting an authentic lamp.

Why avoid a generic Optoma EP719 projector lamp?

Generic lamps have six main problems:

Buy this lamp on Amazon sold by these authorized dealers:

Step Two: Know when to replace

You’ll start to see the following warning signs when the Optoma BL-FU180A  lamp is approaching end of life:

  • A screen that is gradually dimming or deteriorating.
  • Colour in the image appears dark or off colour.
  • Lamp light flashing a steady orange.
  • The following warning sign will appear on screen:

Optoma_EP716_BL-FU180A_lamp_warning

Step Three: Replace the Optoma EP719 projector lamp

Follow these important safety steps before installing a new Optoma BL-FU180A:

  • The used Optoma BL-FU180A contains mercury and should be properly recycled. Don’t throw it into regular garbage.
  • Switch off the power to the Optoma EP719 projector by pressing the Power/Standby button.
  • Disconnect the power cord.
  • Allow the projector to cool down for at least 30 minutes. If should be cool to the touch. These projectors run using high temperatures and you can burn yourself badly if you don’t allow the projector to cool down.

Optoma_EP719_BL-FU180A_remove_lamp_cover
 
Place something soft underneath the Optoma EP719 before turning the projector onto it’s back. Remove the two screws holding the cover in place.
Optoma_EP719_BL-FU180A_remove_cover
 
Push the cover up to remove it.
 
Optoma_EP719_BL-FU180A_remove_lamp_screws
 
Use a screwdriver to remove the two screws holding the Optoma BL-FU180A lamp module in place.
Lift up the wire handle and slowly put out the old lamp. Be careful not to bang the lamp against the projector as this may case the bulb to break. Learn what to do if the lamp has exploded inside the projector.
NOTE: The Optoma BL-FU180A contains mercury and must be properly recycled.
 
Optoma_EP719_BL-FU180A_new_lamp
Place the new Optoma BL-FU180A into the Optoma EP719 projector. Tighten the two screws on the lamp. Replace the lamp cover and tighten its two screws.
Optoma_EP719_BL-FU180A_lamp
You must now reset the Lamp Replacement Timer.

 

Step 4: Reset the lamp timing on the Optoma EP719 projector lamp

Optoma_EP719_BL-FU180A_lamp_reset
The Optoma EP719 projector has an automatic lamp reset timer that tracks the life of the lamp and triggers the lamp replacement warning. You need to reset the timer each time the lamp is replaced.

  • Press the Menu option on either the remote or on the projector.
  • Scroll over the Lamp Setting. Press enter.
  • Select Reset Lamp Hours. Press Enter
  • The Execute/Cancel command line will appear.
  • Scroll over to choose Execute. Press Enter. The lamp hours is reset to zero.

Get the Optoma BL-FU180A  to last longer with these tips:

  • Turning on the Eco Mode to lower power consumption and extend the lamp life by 130%.
  • Keep your air filters clean to avoid overheating the projector.
  • Turn off the Optoma EP719 projector and let it stand for at least one hour ever 24 hours.
  • Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
  • Top tips for extending DLP projector lamp life

Comments

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Shares