Replace the Epson EMP-835p projector lamp

Written by
  • Shelagh M.
  • 9 years ago

Epson_EMP_835p_projectorHere’s how to replace the Epson EMP-835p projector lamp in 3 easy steps.

With their bargain prices and easy availability counterfeit lamps can be a real temptation. Be sure to invest in a genuine Epson EMP-835p projector lamp

Step 1: Buying the right lamp

Counterfeit lamps end up costing you more due to their inferior workmanship. With their bargain prices and easy availability, generic lamps can be a real temptation. But they will end up costing you more due to their inferior workmanship. Be sure to buy an authenticEpson EMP-835p projector lamp in order to keep your projector working properly.
So-called “generic, compatible” lamps can’t be calibrated properly, these knock-off lamps can seriously damage the optics in your Epson EMP-835p. They actually have a much shorter lamp life.
Even more disturbing is the health hazard they pose. Copy cat manufacturers don’t have the resources to buy the proper materials so they resort to using substitutes such as the carcinogenic Krypton-85, a chemical linked to cancer.
Avoid all these problems PLUS keep the warranty on your Epson EMP-835p projector valid. Look for the seal of approval and buy authentic. Learn the 7 Ways to Spot a Counterfeit Lamp.

Step 2: When to replace

The Brightness Control setting on your Epson EMP-835p will determine the lamp life. A high brightness setting will give you up to 2000 hours while a low brightness will give you 3000 hours. Look for the number of hours used on the INFO menu. Watch for any of the warning signs that the indicate the Epson ELPLP31 lamp is reaching end of life:

  • Dark image.
  • Image that has deteriorated.
  • Color in image that appears off.
  • “Replace the lamp” warning flashing on screen.
  • Lamp light flashing a steady orange.

NOTE: If the Lamp light turns red the Epson ELPLP31 lamp is burnt out and should be replaced immediately.

Step 3: Install the Epson ELPLP31

Before installation of the new Epson EMP-835p projector lamp follow these important safety tips:

  • Turn power button off wait for light to stop flashing.
  • Unplug the power cord on the Epson EMP-835p.
  • Allow the Epson EMP-835p projector to cool for one hour – it should be cool to the touch. These projectors run a high temperatures so you can burn yourself very badly if the projector has not cooled enough before being opened up.
  • Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

Epson_Epson EMP-835p_Epson_ELPLP31_lamp_loosen_cover
 

  • The lamp cover is found on top of the Epson Epson EMP-835p projector.
  • Loosen the lamp cover screw — you can’t remove it only loosen it.

 
 
 
Epson_EMP-835p_Epson_ELPLP31_Remove_lamp_cover

  • Slide the Epson EMP-835p projector lamp cover off

Epson_EMP-835p_Epson_ELPLP31_remove_lamp_from projectir

NOTE: The Epson ELPLP31 lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps!
You are now ready to reset the lamp timer.

Resetting the Epson EMP-835p Lamp Timer

The Epson EMP-835 has a lamp timer that tracks the number of hours left for the Epson ELPLP31. Every time you install a new Epson ELPLP31 lamp you must reset the lamp timer to zero. Don’t use the Epson ELPLP31 lamp beyond its recommended usage as this can damages the Epson EMP-835p projector.
Epson_EMP-835p_Epson_ELPLP31_lamp

  • Press the MENU button on either the remote control or on the projector’s control panel.
  • Scroll down to the RESET option.
  • Press Enter
  • Select LAMP-HOURS RESET.
  • Press ENTER to open the prompt screen

Epson_EMP-835p_Epson_ELPLP31_lamp_second_reset_screen
 

  • Press Yes.
  • Lamp hours will be reset to zero.
  • Press MENU to return to the screen.

Tips for longer lamp life

Extend the life of the newly installed Epson ELPLP31 with the following tips:

  • Keep your air filters clean to avoid overheating the projector.
  • Turn off the Epson EMP-835p projector and let it stand for at least one hour ever 24 hours.
  • An average use of four to five hours per day will ensure longer lamp life.
  • Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
  • Set the Brightness Mode to low.
  • Learn more with Top tips for extending DLP projector lamp life

Leave a Reply

Your email address will not be published.

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Shares