Installing a new Epson EMP-400W projector lamp

Written by
  • Shelagh M.
  • 11 years ago

Epson-EMP-400W-projector-Epson-ELPLP42-lampHow to replace the Epson EMP-400W projector lamp

Follow this guide to replace the Epson EMP-400W projector lamp.

Lamp hour notifications

Epson-EMP-400W-warning-light-Epson-ELPLP42-lamp

 
Watch for the signs that the Epson EMP-400W projector lamp needs replacing:

  • Dark image
  • Image that has deteriorated
  • On warning message appears on screen
  • Lamp light flashes orange

Authentic vs generic lamps

In order to keep your Epson EMP-400W working at its optimum levels and to prevent damage, you’ll want to buy an authentic projector lamp. The Internet is flooded with companies offering “generic” compatible lamps. Although they seem like a bargain, these should be avoided. They have some very serious flaws:

Learn how to spot the copycat fake lamps with 7 Ways to Spot a Counterfeit Lamp.

Buy this lamp on Amazon sold by these authorized dealers:

Installing the Epson EMP-400W projector lamp

Before installation:

  • Turn off power switch on the back of the Epson EMP-400W projector.
  • After you turn off the projector’s power and the confirmation buzzer beeps twice, disconnect the power cable
  • Allow the Epson EMP-400W projector to cool for one hour – it should be cool to the touch. Inside of the projector can be very hot since these machines operator under high temperatures and you run the risk of being burned if the projector has not cooled down.
  • Do not operate the projectors while any of the lamps are removed as this may result in malfunctions, fire hazard and other accidents.

Epson-EMP-400W-projector-Epson-ELPLP42-lamp
1. The lamp cover is found on top of the Epson EMP-400W projector. Loosen the lamp cover screw — you can’t remove it only loosen it.
Epson-EMP-400W-remove-cover-Epson-ELPLP42-lamp
2. Slide the Epson EMP-400W projector lamp cover off.
Epson-EMP-400W-loosen_screws_cover-Epson-ELPLP42-lamp
3. Loosen the two screws holding the Epson ELPLP42 lamp in place.
Epson-EMP-400W-remove-lamp-Epson-ELPLP42-lamp4. Grab the Epson ELPLP42 lamp by the two indents on the lamp. Gently remove the lamp. Pulling too quickly can cause the bulb to shatter. Learn what to do should the bulb shatter.
NOTE: The Epson ELPLP42 lamp contains mercury and should not be thrown into regular garbage. Recycle your used lamps!
Epson-EMP-400W-install-new-lamp-Epson-ELPLP42-lamp
5. Gently insert the Epson ELPLP42 lamp making sure it’s facing the right way. NOTE: Don’t touch the screen or the actual bulb with your finger since the oil from your skin can cause a black spot on the bulb.
6. Tighten the screws on the new Epson ELPLP42 lamp.
Epson-EMP-400W-replace-lamp-cover-Epson-ELPLP42-lamp
7. Replace the lamp cover and tighten the screw on the Epson EMP-400W projector lamp cover.
8. Reset the lamp timer.

Reset the lamp timer

Reset the Epson EMP-400W projector Lamp Replacement Counter only when the Epson ELPLP42 lamp has been replaced.
Epson-EMP-400W-replace-reset-lamp-timer-Epson-ELPLP42-lamp

  • Press the MENU button on the remote control. The Lamp Reset Menu will appear.
  • Scroll down to the RESET. Press ENTER.
  • Click on RESET ALL.
  • A prompt appears asking if you want to replace the lamp.
  • Select YES and press ENTER. Press MENU to exit.

 

Prolong the life of the Epson EMP-400W projector lamp:

Extend the life of the newly installed Epson ELPLP42 with the following tips:

  • Keep your air filters clean to avoid overheating the projector.
  • Turn off the Epson EMP-400W projector and let it stand for at least one hour ever 24 hours. An average use of four to five hours per day will ensure longer lamp life.
  • Make sure there is enough airflow around the projector particularly if it’s been permanently mounted.
  • Learn more with Top tips for extending DLP projector lamp life

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Shares